Auto Repair Q&A

Popular

Engine

Cooling System

Brakes

Suspension

Transmission

Exhaust/Emissions

Electrical

Body

Interior

Understand

Directory

Auto Repair Products

how do you replace a thermost in my 1997 chrysler lhs?


try autozone.com free repair

try autozone.com free repair guide photos incChrysler Concorde/Intrepid/LHS/New Yorker/Vision 1993-1997
Thermostat
REMOVAL & INSTALLATION

The thermostat used in these engines is a conventional wax pellet type designed to keep the engine operating at 195°F (90°C). The thermostat opens at approximately 215°F (102°C). so it does do not restrict the flow to the radiator as the coolant temperature rises to around 220°F (104°C). in hot weather. Above 215°F (102°C), the coolant temperature is controlled by the radiator, fan and outside air temperature, not the thermostat.

When the engine is cold, the thermostat is closed and the cooling system has no flow through the radiator. The coolant flows through the engine, heater core, coolant bottle and by-pass. When the engine is warm, the thermostat is open and coolant flows through the radiator, heater core, coolant bottle and bypass.

The engine thermostat is located in the so-called water box formed in the front of the lower intake manifold. This thermostat has an air bleed located in the thermostat housing. Service this vehicle with ethylene glycol base coolant with a silicate inhibitor such as MOPAR® anti-freeze or equivalent in a 50/50 mix with distilled water. The use of aluminum cylinder heads, intake manifolds and water pumps requires special corrosion protection. Chrysler Corp. does not recommend the use of Propylene Glycol as they provide less freeze protection and less corrosion protection.

REMOVAL & INSTALLATION

See Figures 1, 2, 3, 4, 5 and 6

1.Disconnect negative battery cable.

2.Allow cooling system to cool completely. Place a pan under the radiator drain, located at the lower right side of the radiator. Open the valve to drain the cooling system to a level just below the thermostat. Do NOT drain the cooling system completely, unless the coolant is being changed. Close the valve.
3.Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing and if necessary disconnect the hose from the housing.

Fig. Fig. 1: Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing

Fig. Fig. 2: If necessary, separate the upper hose from the thermostat housing (it is not required)

4.Remove the thermostat bolts and housing.

Fig. Fig. 3: Loosen the thermostat housing bolt with the proper size socket

5.Remove the thermostat and discard the gasket. Thoroughly clean both gasket sealing surfaces.

Fig. Fig. 4: Separate the housing to access the thermostat

Fig. Fig. 5: Lift the thermostat out ...

Fig. Fig. 6: ... then clean the mating area

To install:

6.Clean the thermostat housing bolts well. On any engine, bolts that thread into the water jacket are subject to rust and corrosion. A bolt with rust or debris in the threads can easily strip out the threads in an aluminum manifold requiring a time-consuming thread repair operation. Clean the bolts well and lightly lubricate before installation.
7.Install the thermostat into the recess in the intake manifold. Place a new gasket, moistened with water, on the water inlet mating surface on the intake manifold.
8.Install the thermostat housing over the gasket and thermostat and tighten the mounting bolts to 21 ft. lbs. (28 Nm) on the 3.3L engine and 105 inch lbs. (12 Nm) on the 3.5L engine.
9.Connect the upper radiator hose to the thermostat housing and tighten the radiator hose clamp.
10.Refill and bleed the cooling system.

luded

first drain your rad

first drain your rad coolant.follow the upper rad hose to the center of the engine. remove 2 bolts which hold down the thermostat housing. remove thermostat and gasket. reverse steps to install. when refilling coolant make sure to loosen bleeder screw located on top of that thermostat housing. fill with engine off/cool till coolant starts comming out of bleeder hole.


Auto Repair Q&A Contest

Win Cash!

Participate in the 10w40.com Q&A community to win cash prizes!

win cash prizes

Congratulations to our June Winners!

How To Play

 

Top Contributors: 3 weeks