Auto Repair Q&A

Popular

Engine

Cooling System

Brakes

Suspension

Transmission

Exhaust/Emissions

Electrical

Body

Interior

Understand

Directory

Auto Repair Products

i have 2006 nissan altima 2.5 engine. it's not starting i change camshaft sensor, now it's starting but very hard, i check the computer it says cranckshaft sensor and engine speed sensor mulfunction, i cant find the cranckshaft sensor. where is it located


Welcome to 10w40.com The

Welcome to 10w40.com

The crank shaft position sensor in your vehicle is located under the hood in the engine control harness. I have included a picture diagram F11 is the Crank Shaft Position Sensor

Good luck.

06alti2_5L049a.png

did you get the error code

did you get the error code P0725 for the Engine Speed Input Circuit Malfunction as well as the code P0335 Crankshaft Position Sensor A Circuit Malfunction when this happened??? thats what is coming up on my 06 Altima. which number on this diagram is the sensors for these two issues??

Gentlemen, On this particular

Gentlemen,

On this particular engine it’s recommended that you replace both the (CAM)shaft and (CRANK)shaft position senors. Locations of both appear below. (DO NOT) replace (EITHER sensor until you (CONFIRM) the wiring and circuitry for (BOTH) sensors. Understand that:

Wiring issues
Circuit issues
And connection issues (WILL) set a code and (WILL) cause a hard start condition.

Crankshaft position sensor Driver's Side, Rear Side of Engine.

Camshaft position sensor Driver's Side, Below Throttle Body.

call dealer and look into

call dealer and look into this recall, let us know.

Recall 07V527000: ECM Update for Stalling Condition

MAKE/MODELS: MODEL/BUILD YEARS:

Nissan/Altima 2002 2005-2006

Nissan/Sentra 2002 2005-2006

MANUFACTURER: Nissan North America, Inc.

NHTSA CAMPAIGN ID NUMBER: 07V527000

MFR'S REPORT DATE: November 08, 2007

COMPONENT: Engine and Engine Cooling

POTENTIAL NUMBER OF UNITS AFFECTED: 653910

SUMMARY:
On certain passenger vehicles equipped with a 2.5L engine, the crankshaft position sensor can overheat causing a brief interruption in the signal output from the sensor.

CONSEQUENCE:
If the interruption in the signal from the crankshaft position sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at a low speed increasing the risk of a crash.
REMEDY:
Dealers will reprogram the ECM free of charge. Certain M/Y 2006 Altimas which have been previously remedied under recall campaign 06V223000 (Nissan R0606) are not included in this recall since the reprogramming for 06V223000 also included this reprogramming. The recall is expected to begin on or about December 10, 2007. Owners may contact Nissan at 1-800-647-7261.

NOTES:
This is an expansion of a previous campaign (06V223000). Customers can also contact The National Highway Traffic Safety Administration's Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO HTTP://WWW.SAFERCAR.GOV.

I'm busy now. Check back late

I'm busy now. Check back late tonight to see why the recall is a bullshit scam.

Big Block, I see you're a

Big Block,

I see you're a (FORCE TO BE RECKONED) with. :-)

Speaking from (PERSONAL) experience with this (ENGINE) and recall, it should be (INTERESTING) to see where you are (TAKING) this.

right hand side of rear eng

right hand side of rear eng block by bell housing. easy to see by removing top eng cover look down thru the gap between intake manifold ports

Did you get a chance to look

Did you get a chance to look at it?


Auto Repair Q&A Contest

Win Cash!

Participate in the 10w40.com Q&A community to win cash prizes!

win cash prizes

Congratulations to our Rocktober Winners!

How To Play

 

Top Contributors: 3 weeks